CCTV Camera Installation SWMS

Suits security and communications installers fitting CCTV cameras, recorders and cabling in homes, shops, offices and industrial sites. It follows the job from site survey and access set-up through mounting, cable runs, terminations and commissioning to handover. Mains wiring and entry to ceiling spaces are covered by separate SWMS.

A SWMS is legally required when the work is high risk construction work, such as work with a risk of a fall of more than 2 m (WHS Regulation sections 291 and 299). CCTV installation is not high risk by itself, so no box is pre-ticked: tick the falls box if a person could fall more than 2 metres (for example from an elevating work platform or pole), asbestos if it could be disturbed, and any other item that applies. Otherwise this document works as a written safe work procedure or task risk assessment.

Learn More: What Is A Safe Work Method Statement?
Have you ever been asked to provide a SWMS on a project in Queensland? Read our guide to what a Safe Work Method Statement is and when you need one.

What Is Covered In Our CCTV Camera Installation SWMS?

The job steps run in the order the work is done, from pre-start checks to finishing up. The hazards and controls include:

• Falls from ladders, step platforms and EWPs
• Dropped tools and cameras striking people below
• Contact with overhead power lines near poles and eaves
• Drilling into hidden cables, pipes and asbestos
• Silica dust from drilling masonry
• Heat, insulation fibres and stings in ceiling spaces
• Mains-powered recorders and power supplies
• Cuts from cable stripping and cutting
• Overloaded power points and leads
• Trips over cables in public areas

High Risk Construction Work

No high risk construction work items (WHS Regulation 2011 (Qld) s 291) are pre-ticked, because this work is not high risk construction work by itself. Tick the items that apply to your job, such as a fall risk of more than 2 metres or work where powered mobile plant is moving.

Licences, Training and Competency

• General construction induction training card (white card) for construction work, and site induction
• Electrical work licence for any mains wiring or hard-wired mains connection (Electrical Safety Act 2002 s 55); mains work is outside this SWMS
• Cabling registration for communications cabling where it is required; confirm the requirement before the job
• Operator licence or verification of competency for any elevating work platform used; a high risk work licence if it is a boom-type EWP with a boom length of 11 m or more (WHS Regulation Sch 3 item 21)
• Training in ladder and step platform use, and in working near overhead power lines
• Asbestos awareness training (WHS Regulation s 445) for workers who may do asbestos-related work
• Crystalline silica training where the dust assessment finds drilling high risk (WHS Regulation s 529CD)

Legislation and Codes of Practice Referenced

• Work Health and Safety Act 2011 (Qld)
• Work Health and Safety Regulation 2011 (Qld)
• Work Health and Safety Regulation 2011 (Qld): ss 306A to 306N (falls, ladders and trestle platforms in construction work)
• Work Health and Safety Regulation 2011 (Qld): ss 56 and 57 (noise), ss 419, 422, 445, 446 and 450 to 451 (asbestos) and ss 529A to 529CD (crystalline silica)
• Electrical Safety Act 2002 (Qld): ss 14, 18 and 55 (meaning of electrical equipment, electrical work and licence requirement)
• Electrical Safety Regulation 2026 (Qld): s 10 and sch 2 (overhead power line exclusion zones)
• Electrical Safety Code of Practice 2021 – Managing electrical risks in the workplace
• Managing the Risk of Falls at Workplaces Code of Practice 2021
• Hazardous Manual Tasks Code of Practice 2021
• How to Manage and Control Asbestos in the Workplace Code of Practice 2021
• Managing respirable crystalline silica dust exposure in construction and manufacturing of construction elements Code of Practice 2022
• Managing Noise and Preventing Hearing Loss at Work Code of Practice 2021
• Managing the Work Environment and Facilities Code of Practice 2021
• How to Manage Work Health and Safety Risks Code of Practice 2021
• First Aid in the Workplace Code of Practice 2021
• Safe Work Australia model Code of Practice: Elevating work platforms (guidance)

What You Get

• An editable Microsoft Word document (14 pages), laid out on A4 landscape pages
• Business, client, job and document details typed once and filled in on every page, plus a space for your logo
• The high risk construction work checklist, worded as WHS Regulation s 291, and the construction project question (s 292)
• A worker and health and safety representative consultation record
• Qualifications, plant, PPE, hazardous chemicals, safety equipment, permits, references and emergency arrangements filled in for this work
• A 5 x 5 risk matrix, and job steps with initial and residual risk scores and the people responsible
• Implementing, monitoring and review requirements, an additional controls log, revision history and a worker sign-on sheet

Review and adjust it for your site, your plant and the way your crew does the job, and talk it through with your workers before work starts. If you have any trouble downloading this SWMS, you can contact us at any time. Please make sure you read our Disclaimer before downloading this SWMS.