Aluminium Patio and Insulated Roof Installation SWMS

For patio, outdoor living and carport installers who build aluminium frames and fit insulated roof panels to existing homes and buildings. It follows the job from inspecting the building and locating services to footings, the frame, laying panels, flashings and handover.

Most patio installs are high risk construction work because a person could fall more than 2 metres (WHS Regulation s 291(a)), so the falls item is ticked; the 3 metre figure for housing in ss 306C and 306D changes the fall-prevention rules, not this tick. Tick the others that apply: energised electrical installations or services, powered mobile plant when a forklift or crane lifts packs, and asbestos if old eaves or sheeting could be disturbed.

New to SWMS? Read What Is A Safe Work Method Statement?

What Is Covered In Our Aluminium Patio and Insulated Roof Installation SWMS?

After the standard pre-start checks, the job steps run from “Plan the job and inspect the existing building” to “Clean up, check and hand over”. The hazards and controls include:

• Falls from the frame, ladders and roof
• Falls through fragile roofing
• Heavy and long panel handling
• Wind catching panels and frames
• Contact with overhead power lines
• Drilling into walls with hidden services
• Asbestos in old eaves and sheeting
• Silica dust from drilling masonry
• Sharp metal edges and cutting
• Sparks near insulation foam
• Noise from cutting and fixing
• Heat and sun exposure

High Risk Construction Work

These high risk construction work items (WHS Regulation 2011 (Qld) s 291) are already ticked because they are part of this work. Tick any others that apply to your job:

• Involves a risk of a person falling more than 2m

Licences, Training and Competency

• General construction induction training card (white card)
• Site induction
• Installers trained in the patio or roof panel system and its fixings (manufacturer’s installer training where available)
• Training in the fall protection used (platform, scaffold, EWP, restraint or arrest) and in the rescue plan
• Licence for the class of any crane, forklift truck or vehicle loading crane used to lift packs; dogging class or higher rigging class for anyone who slings loads or directs a plant operator when the load is out of the operator’s view (Schedule 3, Schedule 19)
• Boom-type elevating work platform licence for a boom of 11 m or more
• Scaffolding licence for scaffold where a person or object could fall more than 4 m (erected under a separate scaffolding SWMS)
• Licensed electrician for any electrical isolation, relocation or connection of lights, fans and power
• Trained first aider on site

Legislation and Codes of Practice Referenced

• Work Health and Safety Act 2011 (Qld)
• Work Health and Safety Regulation 2011 (Qld)
• Managing the Risk of Falls at Workplaces Code of Practice 2021
• Scaffolding Code of Practice 2021 (where scaffold is used for access)
• Managing Risks of Plant in the Workplace Code of Practice 2021
• Hazardous Manual Tasks Code of Practice 2021
• Managing Noise and Preventing Hearing Loss at Work Code of Practice 2021
• Managing Risks of Hazardous Chemicals in the Workplace Code of Practice 2021
• Managing respirable crystalline silica dust exposure in construction and manufacturing of construction elements Code of Practice 2022
• How to Manage and Control Asbestos in the Workplace Code of Practice 2021
• Excavation Work Code of Practice 2021 (footings)
• First Aid in the Workplace Code of Practice 2021
• How to Manage Work Health and Safety Risks Code of Practice 2021
• Electrical Safety Act 2002 (Qld)
• Electrical Safety Regulation 2026 (Qld): overhead power line exclusion zones
• Electrical Safety Code of Practice 2020 – Working near overhead and underground electric lines (distances come from the 2026 Regulation)
• WorkSafe Queensland guidance: Managing fall risks on roofs in housing construction (guidance, not a code)

What You Get

• An editable Microsoft Word document (13 A4 landscape pages). Type your business, client and job details once and they fill in on every page, with a space for your logo
• 11 job steps for this work, each with its hazards, controls, initial and residual risk scores and the person responsible
• PPE listed for this job: safety boots with good grip; safety glasses; cut-resistant gloves for handling sheet metal and panels; hearing protection where noise cannot be controlled at the source
• Emergency arrangements for: fall from height and contact with a power line
• Plus the parts every Work Safety QLD SWMS shares, from the s 291 checklist to the worker sign-on sheet (see the layout in our free SWMS template)

Adjust it for your site, plant and crew, and talk it through with your workers before work starts. Please make sure you read our Disclaimer before downloading this SWMS.

Checked against the Queensland laws and codes of practice listed above. Last reviewed November 2026.